© Copyright, 2003, all rights reserved • Securitron Magnalock Corp., 550 Vista Blvd., Sparks NV 89434, USA Tel: (775) 355-5625 • (800) MAGLOCK • Fax:
Rev. A.2, 10/03 Page-7 FIG 5: DC LOCK - DC POWER WIRING NC1 C1 NO1AC IN FDC IN /OUT+POWER SUPPLY12 OR 24 VDCDC FAIL SECUREOR FAIL SAFE LOCKMOVIF
Rev. A.2, 10/03 Page-8 lock and if it’s fail secure, the switch will need to send power to the lock. Figure 6 shows how to add external contacts f
Rev. A.2, 10/03 Page-9 When using exit switches, the possibility must be considered that an electronic failure may occur to the DK-26 and a person
Rev. A.2, 10/03 Page-10 FIG. 8: DOUBLE BREAK WIRING FOR FREE EGRESS (SPDT SWITCH) 4. PROGRAMMING The DK-26 has ten numbered keys and a bell key
Rev. A.2, 10/03 Page-11 "traffic control" applications, as the longer the code remains unchanged, the greater the risk that an unauthoriz
Rev. A.2, 10/03 Page-12 codes to be certain that the unit will operate only on the single code you plan to enter. Follow the steps shown below.
Rev. A.2, 10/03 Page-13 After you’ve completed your entries, test your user and program codes by entering them. The user code should open the door
Rev. A.2, 10/03 Page-14 Enter program code, followed by the Bell Key, note rapid yellow flashing LED (program mode) Enter prefix 0-1 followed
Rev. A.2, 10/03 Page-15 button in the CPU board. It is deliberately kept separate from all programming functions. Another use for it, however, is
Rev. A.2, 10/03 Page-16 To delete all User codes, there is a special prefix. Put the unit into program mode (fast yellow flash) from the “Prgm Cod
Rev. A.2. 10/03 SECTION 4.2 KEYPAD CHANGEABLE PROGRAMMING-----------------------------Page 12 This section explains how to set up easy code change
Rev. A.2, 10/03 Page-17 To return the red/green LED logic to factory set default, put the unit into program mode and enter 7-4. 6. USE OF THE PROG
Rev. A.2, 10/03 Page-18 6.3 ANTI-TAMPER ALARM FUNCTION A person attempting to guess the code and pressing 16 wrong digits will put the DK-26 into
Rev. A.2, 10/03 Page-19 6.5 NIGHTLIGHT FUNCTION When this function is selected, the act of touching any key will operate the programmable relay fo
Rev. A.2, 10/03 Page-20 7.3 ALARM SYSTEM SHUNTING The DK-26's lock control relay is of the double pole, double throw type. Note that in all
Rev. A.2, 10/03 Page-21 Put the unit into program mode and enter 8-0 to assign this function to the HCD terminal or 8-1 to assign it to the UCD ter
Rev. A.2, 10/03 Page-22 MAGNACARE® LIMITED LIFETIME WARRANTY SECURITRON MAGNALOCK CORPORATION warrants that it will replace at customer’s request,
Rev. A.2, 10/03 Page-i APPENDIX A: COMMAND SUMMARY WITH THE UNIT IN PROGRAM MODE (FAST YELLOW FLASH): 00 followed by 5-7 digits sets Program code
Rev. A.2, 10/03 Page-ii APPENDIX B: TROUBLESHOOTING Note first that the DK-26 replaces older Securitron keypads: the DK-20, DK-20+ and DK-25. The
Rev. A.2, 10/03 Page-iii If PolySwitch #1 has tripped, visually inspect the four large diodes on the board to see if a loose wire has fallen on the
Rev. A.2, 10/03 Page-iv entry will be ignored. Finally note that if terminals SRC and UCD are connected, all User codes will be disabled. If term
Rev. A.2. 10/03 SECTION 6.3 ANTI-TAMPER ALARM FUNCTION ---------------------------------Page 18 Someone entering 16 wrong digits while attempting
Rev. A.2, 10/03 Page-v PROBLEM-- How to check the Keypad For reference, when each key is pressed, two terminals will measure zero volts with respec
Rev. A.2, 10/03 Page-1 SECURITRON MODEL DK-26 DIGITAL KEYPAD INSTALLATION & OPERATING INSTRUCTIONS 1. DESCRIPTION Securitron's DK-26 is
Rev. A.2, 10/03 Page-2 FIG. 1: PHYSICAL INSTALLATION OF KEYPAD MOUNTINGSURFACE(1) MOUNT SCREW TO ENGAGE SLOT ATTOP OF KEYPADDRILL 1/8" (3MM)
Rev. A.2, 10/03 Page-3 3. WIRING 3.1 POWER SELECTION The DK-26 operates on 12 to 24 volts AC or DC. Nearly all electric locks operate on voltage
Rev. A.2, 10/03 Page-4 FIG. 2: OVERVIEW OF CPU BOARD SRCREXUCD HCD NCX CXNOXNC2 C2NO2NC1 C1NO1GRN YEL RED BLUWHTBLK GRY BRN BGE ORG PNKVIOAC IN F
Rev. A.2, 10/03 Page-5 Note installation of the MOV across the power wires to the lock. The MOV is the small black disk shaped component furnished
Rev. A.2, 10/03 Page-6 reduce the switching life of the relay. The arc also creates electronic noise which could cause the microprocessor to malfu
Kommentare zu diesen Handbüchern